Drives the model through Update with real key messages: a full walkthrough
asserting the config it produces, every validation gate keeping the operator on
the screen with the cursor on the field at fault, and the rendered output for
facts that appear nowhere else (role layout, pool geometry, folded planes).
- partUUID: error on empty blkid output instead of writing UUID= to fstab
- installBootloader: fail if both EFI and BIOS targets fail; track efiErr
- machine-id fallback: write at mode 0600 so systemd can commit on first boot
- Run: defer unmount so partitions are always cleaned up on failure
- copyRootfs: verify critical paths exist after rsync before continuing
- resolveNIC: skip virtual/bridge interfaces (docker0, virbr0, ovs-system)
- EjectAndReboot: use syscall.Reboot instead of exec(reboot) which needs D-Bus
- ui.Run: return error on TTY open failure instead of silent fallback
- firstboot script: trap EXIT to always self-disable, preventing retry loops
- enableUnit/enableBannerUnit: deduplicate into enableSystemdUnit; check Remove
- runAdminBanner: promote service restart failure to slog.Error
- parseNodeConf: log non-ENOENT read failures
- Add spinifex login user password via chpasswd in install.go (same
password as root, collected once in TUI)
- Copy /root/.aws/ to /home/spinifex/.aws/ in firstboot so the operator
can use the AWS CLI without sudo after first boot
- Fix getty drop-ins to be instance-specific (tty1/ttyS0 only), leaving
tty2+ immediately available as rescue terminals
- Remove autologin — node now requires password at login prompt
- Pre-start OVS/OVN in firstboot and poll NB DB up to 120s to eliminate
setup-ovn.sh timeout races on slow physical hardware
- Tighten per-service ownership in firstboot (each service user owns only
its own /var/lib/spinifex subdirectory)
- Add LAN bridge as a non-critical systemd unit so a missing LAN cable
can never stall network-online.target or firstboot
- Write dhcpcd.conf with short br-lan timeout; add networking.service
drop-in to treat exit 1 as success for optional interface failures
- Disable IPv6 on management bridges to silence dhcpcd journal noise
- Fix WAN/LAN enter-key and ESC navigation logic in TUI
- Fix LAN NIC cursor to skip WAN NIC correctly
- Replace single network screen with separate WAN and LAN screens
- WAN/LAN IPs now live on Linux bridges (br-wan, br-lan) over the physical
NICs, not on the NICs directly — makes OVS/OVN veth attachment SSH-safe
- Add DHCP/static toggle on both screens (DHCP is the default)
- Add DNS nameserver input for static mode (comma-separated, default hint
1.1.1.1 / 8.8.8.8 shown as placeholder)
- Detect WiFi NICs via /sys/class/net/<name>/wireless; show SSID and
password fields when a WiFi adapter is selected
- LAN screen shows WAN NIC greyed/unavailable; cursor skips over it
- LAN screen only shown when 2+ NICs are detected
- Geneve encap IP uses br-lan address when LAN NIC present, else br-wan
- Remove --macvlan/--wan-iface from firstboot; setup-ovn.sh auto-detects
br-wan as a Linux bridge and uses veth mode
- Pin both WAN and LAN NIC names to MAC via a single udev rules file
- node.conf writes MANAGEMENT_IFACE=br-wan (bridge, not physical NIC)
- chown /etc/spinifex and /var/lib/spinifex to spinifex:spinifex after
spx admin init so services running as the spinifex user can read configs
- add Environment=HOME=/root to firstboot unit to suppress $HOME warning
- increase wait-for-nats.sh timeout from 30s to 90s for slow startup
- banner now writes to both /dev/tty1 and /etc/motd (visible over SSH)
- add systemd.show_status=1 to GRUB cmdline for per-service boot feedback
- add --removable to grub-install EFI so fallback path EFI/BOOT/BOOTX64.EFI
is written (required for UTM and bare metal without NVRAM boot entries)
- add root password screen and manual NIC entry to installer TUI
- tee spx admin init output to /root/spinifex-credentials.txt with 0600 perms
Replaces charmbracelet/huh with a custom bubbletea wizard for the
installer TUI. This gives full control over terminal I/O so the
installer attaches directly to the correct console device (ttyS0 for
serial, tty1 for VGA) as directed by the new spinifex-init boot script.
- branding/branding.go: centralised logo (ASCII placeholder), color
constants, and publisher string ready for Mulga asset swap
- ui/ui.go: multi-screen bubbletea model (welcome → disk → network →
identity → join → CA cert → confirm) styled with lipgloss
- main.go: reads SPINIFEX_CONSOLE from /proc/cmdline to open the right
tty before launching tea.Program
- go.mod: bubbletea/lipgloss/bubbles promoted to direct deps; huh removed
Adds cmd/installer with three packages:
- ui: huh-based TUI collecting disk, network, node, and cluster config
- install: sequential install steps (partition, debootstrap, chroot, bootloader)
- firstboot: oneshot systemd service that runs setup-ovn and spx admin init/join on first real boot
Supports both single-node init and multi-node join flows.
Julian Sommer